Chevron Digital Timer Socket Manual Download Free Software

• AM/FM Digital Radio INSTRUCTION MANUAL www.tecsunradios.com.au. • Setting display backlight.. 11 Changing MW channel step.12 Setting display contrast.. 13 Checking version..14 DRM memory.. 15 Setting the alarm timer.. 16 Setting snooze..

18 Setting sleep timer.. 19 Setting confirmation beep.20.

• Performing factory reset.21 Switching between DRM/AM/FM modes.22 Volume and Tone control.22 Manual tuning.. 24 Auto scan tuning..26 Presetting stations.. 27 Recalling a preset station.28 Line out..29 Headphone socket.. 29 DRM memory tuning.

• Thank you for choosing Tecsun Radios Australia product. Please read this manual carefully before operating the radio and keep it for future reference. Do not leave the radio near heat sources, such as heaters or hot air ducts, or in a place subject to direct sunlight, excessive dust, humidity, rain, mechanical vibration or shock. • To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Never use an AC power cord that is damaged, route the power cord in a safe manner and make sure it is not exposed to sharp surfaces or the possibility of pinching.

Data sheet, Affected product types, New product packaging for switches 2018. Cyberex SuperSwitch 3 Digital Static Transfer Switch.

• □ □ Display Controls □ Speaker www.tecsunradios.com.au. • □ □ Whip antenna Headphone socket □ FM external antenna jack Line out jack □ AM external antenna jack DC power jack □ □ Antenna switch AC power jack www.tecsunradios.com.au.

• □ BAND selection button TUNING control rotary □ □ SERVICE selection MODE switch button □ □ VF/VM button Volume/Tone control rotary □ □ MENU, INFO button USB port □ POWER ON/OFF button MANUAL TUNE buttons □ PRESET buttons www.tecsunradios.com.au. • Frequency display □ □ Sleep indicator Metre band indicator □ □ Antenna indicator Time indicator □ □ Signal strength Mode indicator □ □ Stereo indicator Preset group-number □ DRM SERVICE indicator Tuning indicator □ □ Frequency dial VF/VM indicator www.tecsunradios.com.au.

• AC operation Before plugging the AC cord into the radio, make sure the AC voltage is correct. Insert the plug on the end of the supplied power cord into the AC power socket on the back of the radio.

DC operation The radio can also be operated by connecting a 9V DC power adaptor with 2.5 Amp capacity and center positive polarity to the DC 9V jack on the rear panel. • The radio comes with built-in AM/FM antenna and external antenna. To use internal antenna, make sure to switch external/internal switch on the back of your radio to internal antenna position (i.e. As for external antenna, you can connect a coaxial cable of outdoor antenna (not supplied) to the BNC type antenna terminal. Press MENU/INFO button to enter the menu settings. Rotate the TUNING control rotary until the ‘Time Set’ entry is shown on the display, then press it to enter the setting. An underline will be shown under the hour setting.

Rotate the TUNING control rotary to select the desired hour, and press the rotary to confirm the setting. Press MENU/INFO button to enter the menu settings. Rotate the TUNING control rotary until the ‘Date Set’ entry is shown on the display, then press it to enter the setting.

An underline will be shown under the month setting. Rotate the TUNING control rotary to select the desired month and press the rotary to confirm the setting and proceed to day setting. Press MENU/INFO button to enter the menu settings. Rotate the TUNING control rotary until the ‘Backlight’ entry is shown on the display, then press it to enter the setting. Rotate the TUNING control rotary to adjust the backlight timeout between always off, 10 seconds, 30 seconds, 60 seconds and always on.

Europe - Carrie.flac 31.93 MB 11. Europe - Rock The Night.flac 31.14 MB 10. Europe - Superstitious.flac 33.59 MB 13. Europe - On Broken Wings.flac 28.8 MB 09. Europe - Cherokee.flac 31.33 MB 12.

Press MENU/INFO button to enter the menu settings. Rotate the TUNING control rotary until the ‘MW Step’ entry is shown on the display, then press it to enter the setting. Rotate the TUNING control rotary to adjust the MW channel step between 9 kHz and 10 kHz. Press MENU/INFO button to enter the menu settings. Rotate the TUNING control rotary until the ‘Contrast’ entry is shown on the display, then press it to enter the setting.